点击图片查看原图
After installing the SKF bearing in Yangzhou, check the operation and check whether the installation is correct. Small machinery can be manually rotated to confirm whether it is rotating smoothly. Because of foreign matter, scar, indentation and other reasons, the inspection items are running poorly. Due to improper installation, small installation space, large installation error, large friction and excessive torque, the torque of the SKF bearing base installed in Yangzhou is unstable. If there is no exception, you can start the power operation.
扬州SKF轴承功率从空载开始缓慢，在规定条件下缓慢增加到额定运行。试运行中的检查项目包括异常声音、滚珠轴承温度变化、润滑油泄漏或变色。如果异常，立即停止操作，检查机器并检查轴承。必要时应清除。
Yangzhou SKF bearing power starts slowly from no load and slowly increases to rated operation under specified conditions. The inspection items in the trial run include abnormal sound, temperature change of ball bearing, leakage or discoloration of lubricating oil. If abnormal, stop operation immediately, check the machine and check the bearing. It should be cleared when necessary.
扬州SKF轴承是工程机械的重要组成部分之一。安装不当会影响使用效果，甚至会导致工程机械设备的故障。
Yangzhou SKF bearing is one of the most important parts of construction machinery. Improper installation will affect the use effect, and even lead to the failure of engineering machinery and equipment.
润滑对轴承的运行和寿命有非常重要的影响。扬州SKF轴承润滑脂由基础油、增稠剂和添加剂制成。润滑脂的性能主要取决于基础油。一般低粘度基础油适用于低温、高速、高粘度、高温、高负荷。
Lubrication has a very important effect on the running and life of bearings. Yangzhou SKF bearing grease is made of base oil, thickener and additive. The performance of grease depends mainly on the base oil. The general low viscosity base oil is suitable for low temperature, high speed, high viscosity, high temperature and high load.
增稠剂也与润滑性能有关。扬州SKF轴承增稠剂的耐水性决定了油脂的耐水性。原则上，不同等级的润滑脂不能混合。即使是相同的稠化油也会因添加剂的不同而产生不良影响。扬州SKF轴承表面涂有防锈油。必须用清洁汽油或煤油清洗，然后涂上优质、高速、高温润滑脂。所有封闭的SKF轴承轴承不必清洗和加油。
The thickening agent is also related to the lubrication performance. The water resistance of Yangzhou SKF bearing thickener determines the water resistance of grease. In principle, different grades of grease can not be mixed. Even the same thickening oil will cause adverse effects due to the different additives. The surface of Yangzhou SKF bearing is coated with antirust oil. It must be cleaned with clean gasoline or kerosene, and then coated with high quality, high speed, high temperature grease. All closed SKF bearing bearings do not have to be cleaned and refueling.
角接触球轴承的结构类似于深沟球轴承，因此装配过程有许多相似之处。
The structure of angular contact ball bearings is similar to deep groove ball bearings, so the assembly process has many similarities.
环形滚道的尺寸偏差与深沟球轴承的尺寸偏差相同。可以使用一些工具、仪器和尺寸符号。采用整体铆接保持架和铆接工艺。检查扬州SKF轴承的径向间隙是控制接触角的大小，并检查成品轴承的实际宽度。
The size deviation of the ring raceway is the same as that of the deep groove ball bearing. Some tools, instruments and size symbols can be used. The holistic riveting cage and riveting process are adopted. Check the radial clearance of SKF bearing in Yangzhou is to control the contact angle and check the actual width of the finished bearing.
从装配库中拆下外圈、内圈、钢球和保持架的基本装配工艺，去除锈蚀和锈蚀，然后分离内外环滚道尺寸。当内套筒和钢球放置在外圈时，可以通过控制径向间隙来选择三个匹配部件的尺寸偏差。在操作扬州SKF轴承过程中，钢球按照规定钢球数分布在外圈和内圈的两个辊道之间，然后测量径向游隙。确认间隙后，取出钢球，将网箱组装好，将内圈、钢球和保持架组合成外圈。
Remove the basic assembly process of the outer ring, inner ring, steel ball and cage from the assembly library, remove rust and rust, then separate the inner and outer ring raceway dimensions. When the inner sleeve and the steel ball are placed in the outer ring, the size deviation of the three matching parts can be selected by controlling the radial clearance. During the operation of Yangzhou SKF bearing, the steel ball is distributed between the two roller paths of the outer ring and the inner ring according to the specified number of steel balls, and then the radial clearance is measured. After the clearance is /confirm/ied, the steel ball is removed, the cage is assembled, and the inner ring, the steel ball and the cage are combined into an outer ring.
文章来自：扬州SKF轴承 www.wh-skf.com
The article comes from: Yangzhou SKF bearing www.wh-skf.com
文章来自：扬州INA轴承 www.ina-china.cn
The article comes from: Yangzhou INA bearing www.ina-china.cn
文章来自：扬州NSK轴承 www.klbbearings.com
The article comes from: Yangzhou NSK bearing www.klbbearings.com
QQ：524085168
电话：0510-81207777
手机：13311666672